China bs en iso 4957 high speed tool steel

China bs en iso 4957 high speed tool steel

We are one of leading company in manufacturing, supplying, trading, distributing and exporting STAINLESS STEEL & HIGH NICKEL ALLOYS PIPE, Tubes, Capillary Tubes, FASTENERS, BOLT, NUTS, WASHER, FLAT Bar, ROUND / SQUARE / HEX BAR, WIRE, Sheets, Plates, Coils etc..

If none of the above grades, sizes, or products ,you can contact us directly, we will offer good advice ! Email: [email protected]

Our Best China bs en iso 4957 high speed tool steel Products

HS6-5-2 / 1.3339 - SteelNumber - Chemical composition,

High-speed tool steel Standard: EN ISO 4957: 2000 Tool steels Equivalent grades: Go here Chemical composition % of steel HS6-5-2 (1.3339): EN 4957-2000 C Si Mn P S Cr Mo W V 0.8 - 0.88 max 0.45 max 0.4 max 0 Post free buying requirement of ...

Read More

China Steel Suppliers - Longhai Special steel

Longhai special steel can manufacture and sales Stainless steel,Tool steel,Alloy,Round bar,Forging,Sheet,Coil,Flat bar,Pipe,Lrregular,Special steel,Through the eu the authentication, the international ISO certification, military quality, China's largest

Read More

1.3343, HS6-5-2, AISI M2, S6-5-2 - HS steel - Virgamet

S6-5-2, HS6-5-2, 1.3343 - specification and application High-speed steel with very good efficiency, ductility, resistance to abrasion and torsion, and impact strength used to work with products with a strength of more than 830 MPa. It is used in the production of drills ...

Read More

X37CrMoV5-1 Steel Chemical composition, Metal

Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. X37CrMoV5-1 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Read More

China Tool Steel, Tool Steel Manufacturers, Suppliers,

China Tool Steel manufacturers - Select 2020 high quality Tool Steel products in best price from certified Chinese Die Steel manufacturers, High Speed Tool Steel suppliers, wholesalers and factory on Made-in-China.com

Read More

Conventional tool steel, a wide range of tool steels - Zapp

We offer a large selection of other tool steels at Zapp, e.g. Cold working steel, hot working steel, high speed steel, plastic mold steel and precision flat steel. Wide range of tool steels In addition to powder-metallurgical steel, you will find a large selection of other tool steels at Zapp. ...

Read More

China High Strength Plat Steel Material O1 1.2510 Sks3

Steel, Alloy Steel, Mould Steel manufacturer / supplier in China, offering High Strength Plat Steel Material O1 1.2510 Sks3 Df2, S7 1.2355 Die Alloy Tool Mould Steel Plate Sheet Flat Steel Round Bar, 1045 Ck45 1040 1050 S45c S50c Carbon Steel Plate Sheet Flat

Read More

Tool steel from Zapp: HSS steel

Along with tool steel such as cold & hot working steel, HSS steel, precision flat steel, plastic mold steel, extraordinarily high performance: PM steel More about our range of conventional tool steels, including cold working steel, hot working steel, plastic mold steel, precision flat steel etc.

Read More

SKH59 Tool Steel JIS G4403 high speed steel grade

Otai Speical Steel are suppliers of SKH59 tool steel in round bar, plate, sheet and block which can be bandsaw cut to your requirements. A high carbon high chromium,high molybdenum, high cobalt, high speed tool steel grade offering very high wear resistance

Read More

AISI M2 1.3343 SKH51 - Xingsheng Special steel

AISI M2 high speed tool steel manufacturers and suppliers, supplied in round bar,square bar,flat bar,plate,sheet and wire.M2 is a molybdenum high speed steel,as a standard, it is most widely used industrial HSS.It has small and evenly distributed carbides giving ...

Read More

Daye Special Steel Co., Ltd. - Hubei

Daye Special Steel Co., Ltd. (Daye Special Steel for short) is located in Huangshi City, Hubei Province. In May 1993, with the approval of Hubei Reform Commission, as the major sponsor for the main part in its production and operation, Daye Steel Plant, Dongfeng ...

Read More

Special Steel - Supplies Special Steel, Supplies Tool

As an ISO 9001 accredited special steel supplier we can help and advise on those hard to find special Steel Specifications including British Standard BS970 specifications and BS EN ISO 4957 grades. With a wide stock range, you'll find Tool Steel

Read More

Special Steel & Stainless steel supplier

As an ISO 2000 accredited special steel supplier we can help and advise on those hard to find special Steel Specifications including British Standard BS970 specifications and BS EN ISO 4957 grades. With a wide stock range, you'll find Tool

Read More

ISO 18265:2013(en), Metallic materials ? Conversion of

The tensile test method used is equivalent to that specified in ISO 6892-1, and the calibration procedures conform with those specified in ISO 7500-1 and ISO 9513. Annex G contains the results on the conversion of hardness values of two tool steels with the assistance of the Verein Deutscher Eisenhüttenleute (VDEh) which were obtained in the year 2007.

Read More

International standard for grades of wrought tool steels

BSI, the business standards company, has revised its standard for cold formed welded steel. BS EN ISO 4957:2018 Tool steels replaces the previous version of this standard published in 1999. The revised standard will be of particular interest to producers of wrought ...

Read More

1.2842, 90MnCrV8, AISI O2 - tool steel

1.2842, 90MnCrV8, AISI O2 - specification and application Tool steel for cold working with high hardenability, high hardness, abrasion resistance and high cutting edge sharpness. The grade is not susceptible to deformation during heat treatment, shows high ...

Read More

Tool Steel Supplier - West Yorkshire Steel - Only £25 UK

Plastic mould steel specifications are held in International Standards such as BS4659, BS EN ISO 4957, AISI, Werkstoff Nr and DIN designations. Plastic mould tool steel grades offer a high wear resistance, good polishability and etching ability with adequate

Read More

BS Steel

tool steel became known and produced in the UK as BO1. A comprehensive range of tool steels were first published in 1971 under the British Standard BS4659. In 2000 a new series of tool steel specifications were introduced as BS EN ISO 4957. Below we list

Read More

ISO 4957:1999(en), Tool steels

high-speed tool steels steels used mainly for machining and for forming processes and which, because of their chemical composition, have the highest high-temperature hardness and temper resistance up to about 600 C Only informative sections of standards ...

Read More

Stainless Steel and Aluminium Services, Stockists &

Aluminium & Stainless Steel Suppliers, Stockholders Services. Stainless steel and aluminium services bars, plate, tool steel Wolverhampton West Midlands UK Our tool steel grades are supplied to the British Standard (BS4659 BS EN ISO 4957), the European

Read More

EN10027-1_

Examples of steel names Standard EN ISO 4957 Steel name according to EN 10027-1 X100CrMoV 5 X38CrMoNb16 X10CrNi18-8 EN 10088-2 X6CrMoNb17-1 X5CrNiCuNb16-4 No standard available X30NiCrN15-1-N5 22 EN 10027-1:2005 (E) Table 15 High speed

Read More

TECHNICAL DATA COMPARISON OF MATERIAL JIS AND RELATED

1277 1278 [TECHNICAL DATA] COMPARISON OF MATERIAL JIS AND RELATED OVERSEAS STANDARDS (1) 15NiCr13 20NiCrMo2 20NiCrMoS2 20NCD2 40XH 15X 15XA 20X 30X 35X 40X 45X 20XM 20XM 30XM 30XMA 35XM 34Cr4 34CrS4 17Cr3 17CrS3

Read More

ISO 4957:1999 - Techstreet

high-speed tool steels. If not stated otherwise, this International Standard applies to all types of hot-rolled, forged, cold-drawn or cold-rolled products which are supplied in one of the surface and heat-treatment conditions given in 4.1.2 and Table 1.

Read More

DIN EN ISO 4957 : 2001-02 TOOL STEELS SAI Global

Buy DIN EN ISO 4957 : 2001-02 TOOL STEELS from SAI Global Vorwort 1 Anwendungsbereich 2 Normative Verweisungen 3 Begriffe und Definitionen 4 Anforderungen 5 Prüfung und

Read More

DIN EN 1.2379 Steel X153CrMoV12 Material Equivalent,

DIN EN 1.2379 Steel (X153CrMoV12 Material) DIN 1.2379 Steel (X153CrMoV12 Material) is a high carbon chromium molybdenum vanadium cold worked tool steel with high wear resistance, good dimensional stability, toughness and hardenability. Due to the ...

Read More

Designation systems for steels - Part 1: Steel names

EN 10027-1:2005 (E) 6 4.3.2 For steels specified in CEN member's national standards and for other steels, steel names shall be allocated by or under the responsibility of the national standards body concerned. So as to avoid a variety of steel names being

Read More

Longhai Special Steel Tool Steel,Stainless Steel,Bearing

LonghaiSteel has a complete set of advanced modern technological equipment for smelting, machining, product analysis and testing. We offer special steel and titanium alloy products. Our equipment includes billet casters, high precision alloy steel bar and

Read More

BS EN ISO 4957:2018 - Tool steels

Purchase your copy of BS EN ISO 4957:2018 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available online in electronic and print

Read More

What is the Difference Between ISO 4957, BS EN ISO 4957

What is the difference between ISO 4957, EN ISO 4957, BS EN ISO 4957 vs DIN EN ISO 4957 tool steel Standard ? There will be a lot of people who are confused by those similar standards with the same ISO 4957. Are they same or are there any differences

Read More

Huangshi Chengquan Metal Material Co., Ltd.

DIN1.3355 Skh2 (BS EN ISO 4957) DIN1.3355 SKH2 HS18-0-1 ... ESR Products Skh55 M35 DIN1.3243 High Speed Steel SKH55 features: SKH55 s ize: SKH55 프세스: ... FOB : ...

Read More

Special Steel & Stainless steel supplier

Welcome to Longhai Special Steel Co., Ltd. A state run business with over 30 years experience in delivering special steel. As an ISO 2000 accredited special steel supplier we can help and advise on those hard to find special Steel Specifications including British Standard BS970 specifications and BS EN ISO 4957 grades. ...

Read More

High-speed steel - Wikipedia

High-speed steel (HSS or HS) is a subset of tool steels, commonly used as cutting tool material. It is often used in power-saw blades and drill bits. It is superior to the older high-carbon steel tools used extensively through the 1940s in that it can withstand higher temperatures without losing its temper (hardness). This property allows HSS ...

Read More